Your online discount source for SEPCO pump and valve packing!  |  Call (704) 298-1103 or (800) 618-2898  |  Fax (704) 220-2262

PTFE (Teflon) Packing

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2
  1. Image of SEPCO 219 | Vegetable fiber / PTFE pump packing

    Starting at: $30.10

    Construction: Square Braid
    Features: Highest quality vegetable fiber. All bark, coarse and short fibers have been removed.
    Treatment: Impregnated with PTFE dispersion and a special break-in oil.
    Equipment: Reciprocating and rotary shafts. Stern tube packing.
    Recommended For: Brine, cold water and cold oil.
    Service Conditions: Shaft speeds to 1885 FPM; temperatures to 220°F/104°C; pH range 5-9.
    Remarks: PTFE impregnate acts as: (1) a surface leveler filling any surface voids. (2) a saturant to prevent wicking. (3) a lubricant to reduce friction and heat. (4) a protective shield around the flax fibers, preventing fluid penetration and fiber break down.

    Most metric sizes in stock.

    Learn More
  2. Image of SEPCO 2210 Braided PTFE Gasket Tape

    Starting at: $97.67

    Construction: Braided tape
    Features: Unlike other PTFE fluocarbon filament packing, SEPCO pre-lubricates the yarns to provide a softer, more flexible packing, with improved peripheral speed characteristics and exothermic properties.
    Equipment: Glass and glass-lined pipe flanges, Glass and glass-lined pipe vessels, Stainless steel reactors, Ceramic-lined tanks and vessels.
    Recommended For: The most severe services. All oxidizers and corrosives with one exception: molten alkali metals.
    Limitations: Temperature up to 500°F/260°C; pH range 0 - 14.
     

    Most metric sizes in stock.

    Learn More
  3. Image of SEPCO 2225 Teflon Impregnated Packing

    Starting at: $42.23

    Construction: Plait Braid
    Features: Yarns are coated in PTFE suspensoid. This system of impregnation assures even distribution of the PTFE. The fibers are saturated and sealed with the PTFE particles, protecting the fibers from chemical action.
    Surface Treatment: A surface coating of PTFE is applied after braiding. To assure good break-in characteristics, a special high temperature synthetic lubricant is added.
    Equipment: General service on rotary and reciprocating pumps, agitators.
    Recommended For: Caustics, mild acids, difficult chemicals, air, gases, solvents, oils, general chemical plant applications.
    Service Conditions: Shaft speeds to 1885; temperatures to 500°F/260°C; pH 3-11.
    SEPCO ML2225 packing is the same as SEPCO 2225 packing except multi-lok braided.

    Most metric sizes in stock.

    Learn More
  4. Image of SEPCO 2250 valve packing

    Starting at: $46.95

    Construction: Plait Braid
    Features: Yarns are coated in PTFE suspensoid. This system of impregnation assures even distribution of the PTFE. The fibers are saturated and sealed with the PTFE particles, protecting the fibers from chemical action.
    Surface Treatment: A surface coating of PTFE is applied after braiding. No oil or lubricant is added.
    Equipment: Valves, flanges, expansion joints.
    Recommended For: Valve service and static gasket applications, caustics and mild acids.
    Service Conditions: Temperatures to 500°F/260°C; pH 3-11.
    Remarks: Use wherever break-in oil is undesirable.
    SEPCO ML2250 packing is the same as SEPCO 2250 packing except multi-lok braided.

    Most metric sizes in stock.

    Learn More
  5. Image of SEPCO ML2225HC hollow core packing

    Starting at: $42.23

    Construction: Multi-Lok braid over hollow core silicone center
    Features: Yarns are coated in PTFE suspensoid. This system of impregnation assures even distribution of the PTFE. The fibers are saturated and sealed with the PTFE particles, protecting the fibers from chemical action.
    Surface Treatment: A surface coating of PTFE is applied after braiding. To assure good break-in characteristics, a special high temperature synthetic lubricant is added.
    Equipment: General service on rotary pumps, mixers, agitators.
    Recommended For: Caustics, mild acids, difficult chemicals, air, gases, solvents, oils, general chemical plant applications.
    Service Conditions: Shaft speeds to 1885; temperatures to 500°F/260°C; pH 3-11.

    HOLLOW CORE PACKING
    SEPCO’s Hollow Core packings are specifically designed to seal large rotating equipment like mixers and agitators. Testing has proven that a high quality braided packing with a rubber core will outlast conventional packing in applications associated with excessive shaft deflection on large shafts.
    Styles: All packing styles are available in Hollow Core design.
    Sizes Available: 1/2” and up.
    Core Material: Silicone; standard (others upon request).
    Hollow Core: For rotating equipment.

    Most metric sizes in stock.

    Learn More
  6. Image of SEPCO ML2225 pump packing

    Starting at: $42.23

    Construction: Multi-Lok Braid
    Features: Yarns are coated in PTFE suspensoid. This system of impregnation assures even distribution of the PTFE. The fibers are saturated and sealed with the PTFE particles, protecting the fibers from chemical action.
    Surface Treatment: A surface coating of PTFE is applied after braiding. To assure good break-in characteristics, a special high temperature synthetic lubricant is added.
    Equipment: General service on rotary and reciprocating pumps, agitators.
    Recommended For: Caustics, mild acids, difficult chemicals, air, gases, solvents, oils, general chemical plant applications.
    Service Conditions: Shaft speeds to 1885 FPM; temperatures to 500°F/260°C; pH 3-11.
    SEPCO 2225 packing is the same as SEPCO ML2225 packing except square braided.

    Most metric sizes in stock.

    Learn More
  7. Image of SEPCO ML2225A Aramid Reinforced General Service Packing

    Starting at: $53.46

    Construction: Multi-Lok Braid
    Features: Yarns are dipped in PTFE suspensoid insuring even distribution of the PTFE. The fibers are saturated and sealed with the PTFE particles, protecting the fibers from chemical action. The PTFE provides the packing with a greater degree of chemical inertness, lower coefficient of friction and prevents penetration of chemical fluids. The corner tracks are made from an Aramid filament yarn to reduce extrusion and increase pressure and strength characteristics.
    Surface Treatment: A surface coating of PTFE is applied after braiding. To assure good break-in characteristics, a special high temperature synthetic lubricant is added.
    Equipment: General service, rotating and reciprocating pumps, agitators.
    Recommended For: Caustics, mild acids, difficult chemicals, air, gases, solvents, oils, general plant applications.
    Service Conditions: Shaft speeds to 1885 FPM; temperatures to 500°F/260°C; pH 3-11.

    Most metric sizes in stock.

    Learn More
  8. Image of SEPCO ML2235 Hollow Core Teflon Packing

    Starting at: $83.96

    Construction: Multi-Lok Braid
    Features: Unlike other PTFE fluocarbon filament packing, SEPCO pre-lubricates the yarns to provide a softer, more flexible packing, with improved peripheral speed characteristics and exothermic properties.
    Equipment: Any equipment where braided packing is commonly used.
    Recommended For: The most severe services. All oxidizers and corrosives with one exception: molten alkali metals.
    Limitations: Shaft speeds to 1202 FPM; pH range 0 - 14.
    Remarks: No glazing at higher speed applications, inert, virtually indestructible lower coefficient of friction, thermal resistance to 500°F/260°C; and high compression strength.

    HOLLOW CORE PACKING

    SEPCO’s Hollow Core packings are specifically designed to seal large rotating equipment like mixers and agitators. Testing has proven that a high quality braided packing with a rubber core will outlast conventional packing in applications associated with excessive shaft deflection on large shafts.
    Styles: All packing styles are available in Hollow Core design.
    Sizes Available: 1/2” and up.
    Core Material: Silicone; standard (others upon request).
    Hollow Core: For rotating equipment.

    Learn More
  9. Image of SEPCO ML2235 PTFE Packing

    Starting at: $87.78

    Construction: Multi-Lok Braid
    Features: Unlike other PTFE fluocarbon filament packing, SEPCO pre-lubricates the yarns to provide a softer, more flexible packing, with improved peripheral speed characteristics and exothermic properties.
    Equipment: Any equipment where braided packing is commonly used.
    Recommended For: The most severe services. All oxidizers and corrosives with one exception: molten alkali metals.
    Limitations: Shaft speeds to 1202 FPM; pH range 0 - 14.
    Remarks: No glazing at higher speed applications, inert, virtually indestructible lower coefficient of friction, thermal resistance to 500°F/260°C; and high compression strength.

    Most metric sizes in stock.

    Learn More
  10. Image of SEPCO ML2236 FDA Approved PTFE Packing

    Starting at: $100.04

    Construction: Multi-Lok Braid
    Features: Pure PTFE filament lubricated with a proprietary lubricant that satisfies FDA requirements. Unlike other PTFE fluocarbon filament packing, SEPCO pre-lubricates the yarns to provide a softer, more flexible packing, with improved peripheral speed characteristics and exothermic properties.
    Equipment: Any equipment where braided packing is commonly used.
    Recommended For: Applications requiring food grade packing in the food processing industry or where an FDA food grade material is required.
    Limitations: Shaft speeds to 1202 FPM; temperatures to 500°F/260°C; pH range 0 – 14.

    Most metric sizes in stock.

    Learn More

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2